I bought an Amsoil dry filter for my Roto Fab. It seems as if the whole thing must be uninstalled to change the filter.

There is no room in the box that contains the filter to remove it by just loosening the clamp.

This CAI was installed by the dealer before I bought the car and I do not have any installation instructions for it.

Is there anything that I should be aware of if I dismantle this thing to change filters? I know that I don't have to change it now as I have very few miles on it, but I would like to swap the filters anyway.

Thanks for any instructions on how to do this swap.

loosen clamp.,..

pull filter towards fender and up and same time... pops right out man,done mine a few times already

Thanks Shane. That is what I would expect, but after a quick glance yesterday it looked real tight in there. Obviously it can be done, so I will have at it today.

I changed the filter today. The crack team at the dealer that installed this had the screw on the clamp in the 7 o'clock position. Impossible to get a wrench or screw driver on it. I was able to rotate the filter so I could loosen the clamp.

It is a little tight, but not too difficult to change the filters. I really like having the dry filter on there, and it looks great.

I changed the filter today. The crack team at the dealer that installed this had the screw on the clamp in the 7 o'clock position. Impossible to get a wrench or screw driver on it. I was able to rotate the filter so I could loosen the clamp.

It is a little tight, but not too difficult to change the filters. I really like having the dry filter on there, and it looks great.
part number for amsoil filter?

Amsoil part number is: EAAU6065

Will attempt to post picture.

http://img.photobucket.com/albums/v260/fb342/IMG_0056.jpg?t=1246893065

I was looking at a Roto-Fab CAI and I wanted to use a dry air filter. I have a friend that swears by AEM filters. Anyone know the dimensions or maybe the part number for AEM Dryflow air filters?

i am using the dry filter that came with the intake its made by AFE and its cleanable with soap and water.

Where did you order this dry filer? I am interested in getting one for my Roto-Fab. Thanks



Amsoil part number is: EAAU6065

Will attempt to post picture.

http://img.photobucket.com/albums/v260/fb342/IMG_0056.jpg?t=1246893065

Where did you order this dry filer? I am interested in getting one for my Roto-Fab. Thanks

You can buy the S&B Cone Filter that Roto-Fab Sells with all their Intake Units separately! The part number is a RO921. Hope this helps, as they are only about $40 from Roto-Fab. You can place your order here:

http://shop.roto-fab.com/searchquick-submit.sc?keywords=RO921

Here is also the Contact information:

Roto-Fab LLC 10714W 900S-90 Warren IN 46792
shop: 260.375.4480 fax: 260.375.7020
email: sales@roto-fab.com (sales@roto-fab.com)

Is that the DRY filter?

Seems like its the same one that I already have.

I did some checking on line and the S&B filters are very good.

http://www.thetruthaboutfilters.com/

I just worry about the Mass Air and Oil issue that can arise.




You can buy the S&B Cone Filter that Roto-Fab Sells with all their Intake Units separately! The part number is a RO921. Hope this helps, as they are only about $40 from Roto-Fab. You can place your order here:

http://shop.roto-fab.com/searchquick-submit.sc?keywords=RO921

Here is also the Contact information:

Roto-Fab LLC 10714W 900S-90 Warren IN 46792
shop: 260.375.4480 fax: 260.375.7020
email: sales@roto-fab.com (sales@roto-fab.com)